Sportbike Rider Picture Website
|More Information on the Honda CBR900RR|
CBR900RR (893cc) SC28
The first generation CBR900RR was introduced in 1992 with an 893 cc (54.5 cu in) inline-four engine. It set a precedent for light weight in the super bike class, being much lighter than other large-displacement bikes of the time. The CBR900RR was based on an advanced research stage model known within Honda as the "CBR750RR". With the objective of equaling the acceleration of competitors’ flagship sport bikes, Honda increased the stroke of its inline 4-cylinder 750cc engine and thus raised displacement to 893cc. Complementing its power performance were the bike’s dry weight of just 185 kg, wheelbase of 1,405 mm and a body almost identical to that of the advanced research stage model. At 453 lb (205 kg) wet weight, it was by just 4 lb (2 kg) heavier than the CBR600F2, while the next-lightest over-750cc machine, the Yamaha FZR1000, was heavier by 76 lb (34 kg).
Changes for the 1994 model comprise a new shift drum to improve notchy gear shifts. The second-generation CBR900RR, which debuted in 1995, incorporated changes in damping rates and spring rates. The front fork was upgraded with a compression adjuster. The upper cowl stay went from steel to aluminum, and the cylinder head cover went from aluminum to magnesium. The styling of the bike also became more aggressive: The independent dual lights became irregular-shaped multi-reflector lights known as "fox eyes" set further back and covered to improve aerodynamics, and the bike had fewer of the RR's unique fairing "speed" holes. The foot pegs were firmer and slimmer like that of the RC45 and the reversed pedal on the original was replaced with a shift linkage. Instead of measuring speed from the front wheel the speed is measured from the countershaft sprocket with an electronic speedometer.
CBR900RR (919cc) SC33
1996 brought major changes to the CBR900RR with the third generation CBR900RR. To optimize rigidity Honda revised the suspension and chassis. Larger thinner-walled extrusions for more torsional rigidity were used in the swingarm and frame, revised shock and fork internals and 5 mm (0.2 in) raised swingarm pivot. The handle bars were raised by 10 mm (0.4 in)and swept back by five degrees to improve the riding position. A 1 mm (0.04 in) bore increase raised the engine displacement to 918 cc (56.0 cu in). Other revisions included a smaller alternator, the addition of a throttle position sensor, extra clutch plates, and a larger exhaust.
The only changes for the 1997 model were graphics and color options.
In 1998, Honda continued subtle refinements in the fourth generation CBR900RR's chassis. It got a stiffer frame more like the original, offset on the triple clamp reduced by 5 mm (0.2 in). Brakes got larger rotors on the front and new calipers and ergonomics was revised with raised footpegs. The engine got revised with 80 percent new internals in an effort to reduce friction and weight. Cylinders bore got an aluminum composites treatment and new pistons. It also got a larger radiator and a new exhaust header in stainless steel.
CBR929RR (929cc) SC44
The fifth generation CBR900RR, known as the CBR929RR in North America, was introduced in 2000. It has a completely new 929 cc (56.7 cu in) engine, more oversquare with lighter internals. The engine also featured fuel injection and larger valves set at a narrower angle. A new all-titanium exhaust system equipped with HTEV was incorporated. The swingarm is mounted to the engine with bracing under the engine. Larger front disk rotors 330 mm mounted were also fitted and the wheel diameter was increased from 16 inches to 17 inches. The new front fork now used upside-down construction.
CBR954RR (954cc) SC50
The sixth generation CBR900RR was introduced in 2002, in North America and Japan known as the CBR954RR. The cylinder bore was enlarged from 74mm to 75mm, increasing capacity to 954 cc (58.2 cu in). Larger fuel injectors, larger radiator, re-mapped electronic fuel injection, and a more powerful ECU were added. The restyled bodywork and fairings gave a sleeker look. The frame as well as the swingarm were strengthened, and the footpegs raised to allow for greater lean angles. Front disc size increased to 330 mm. Dry weight was reduced to 168 kg (370 lb)and the wet weight to 195 kg (430 lb). Power at the rear wheel is 130.8 hp (97.5 kW) and 67.2 lb·ft (91.1 N·m) of torque.
John McGuinness won the Macau Grand Prix in 2001.
The CBR900RR was replaced by the CBR1000RR in 2004.
All specifications are manufacturer claimed unless specified.
The photo 1995-Honda-CBR900RR-18903-GP.jpg (1995 Honda CBR900RR - Heres a customers bike that Im modifying. It presently has a f-4 front end, and a crea carbonfiber body kit. Im going to port the head, add 1mm bigger valves, put a 945 kit in it, and add erion cams. Were also going to put a ZX-7RR front end on it. On the rear were putting a rc-51 singleside swingarm. Once we get that done, a custom underseat exhaust is next. As long as the money keeps coming in, anything is possible. A blackbird motor???? It can be done!) was uploaded by: [email protected]
Please note, we do not have accessories, motorbikes, motor cycles, motorcycles, or motorcycle gear for sale. This site is dedicated to displaying bike images of Aprilia, Bimota, Harley Davidson, Honda, Kawasaki, Suzuki, Triumph, Yamaha, and other sportbikes.